You can install our site as a web app on your iOS device by utilizing the Add to Home Screen feature in Safari. Please see this thread for more details on this.
Note: This feature may not be available in some browsers.
@JT_M3P are you able to adjust the Trunk Closing Speed? When I hold down the Tailgate button, I can't seem to get it past 3 consecutive beeps. I've seen other videos of the older Hansshow silver metallic control box go up to 6 beeps for the fastest trunk speed setting.
What’s with these ridiculous version number bumps? v6 now? This time next year it’ll be like version 20 or something.
What’s more the differences between each version are, as far as I can tell, opaque. I would not feel confident buying v4 or whatever the latest version is this week when another version might come down the line that fixes problems like the above.
The fact the control box has gone from a metal one with diagnostic LEDs to a plastic one with nothing, with instructions that reference buttons that no longer exist, etc is disconcerting too.
@TM3Matt Are you still having issues with your trunk?
I had my V4 in for 3 months and now is not opening or closing at all. I can power cycle it and it'll work for a day then stop, power cycle again and it stops working after a short drive. Reached out to their support, let's see what they say.
Did you get this figured out on how to adjust the close sensitivity?Hi all, I received exactly the same version. Just installed today to the operational point, will replace all trim pieces tomorrow. Seems to operate opening and closing no issues. However, the instructions speak of the tuning options for opening strength and also the locking strength. It refers erroneously to a small black button on the control unit. This does not exist on this model. Anyone figure out the procedures? Hansshow is a no show in terms of support so far.
I’ll also publish a video soon showing some tips and tricks I learned for making install easier and cleaner.
If it isn't able to close on the selected speed it will re-open slightly and close at a faster speed....Did you get this figured out on how to adjust the close sensitivity?
Same......I've had the Hanshow power frunk and trunk for about 6 months now. Recently, the trunk would pop but not open maybe 1 out of 10 times. Now, it won't open at all without a little help. By a little, I mean I can lift it with just a finger and it will motor up. Otherwise it just pops and then fails to open. I attached a video showing what it does. I tried adjusting the latch and the opening strength to no avail. I also tried contacting Hanshow but they still haven't gotten back to me. I did notice the left strut has a small amount of fluid coming out of it. Maybe the strut went bad? Has anyone had this issue? Or have any other ways of contacting Hanshow for support? I tried email and Whatsapp. Thanks!
Same issue. You need to put your foot on the brake then you will see that it’s no longer greyed out and works!Similar to the original post topic, I ran into a scenario where the Trunk fails to close when attempting to press the Close button on the Tesla Screen.
Has anyone else run into this issue?
Scenario: Open Trunk via new Tailgate button and Close using the Tesla Screen.
The Closed button is greyed out on the Tesla Screen and does not let you press close on the screen.
Specs:
- 2020 Model 3 Performance-
- Tesla Software v2020.44.25
- Hansshow Power Trunk v4 (w/CAN Bus installed)
- Hansshow Control Box (new black plastic box, firmware version: unknown)
You need to put your foot on the brake. Then it will no longer be greyed out and you can close it from the screen.Similar to the original post topic, I ran into a scenario where the Trunk fails to close when attempting to press the Close button on the Tesla Screen.
Has anyone else run into this issue?
Scenario: Open Trunk via new Tailgate button and Close using the Tesla Screen.
The Closed button is greyed out on the Tesla Screen and does not let you press close on the screen.
Specs:
- 2020 Model 3 Performance-
- Tesla Software v2020.44.25
- Hansshow Power Trunk v4 (w/CAN Bus installed)
- Hansshow Control Box (new black plastic box, firmware version: unknown)