Search results

need remove all that, hub and axle nut need to push back in order slide new longer stud in.

16-24 CAMARO SS 1LE FRONT OEM BRAKE ROTOR , (SLIGHT SHAVE FOR CENTER HUB RING) 23142500 (LH) 23189768 (RH) caliper is off CTS-V GEN 2 SPACERS 10MM + LONGER CALIPER BOLTS BRAKE LINE IS OFF MODEL 3 - STEEL BRAIDED

the left tailight come out w/ the charge door. (best option) or you can disconnect the charge unit and get access to the nuts circle red.

If your battery still cover under warranty it's free. I end up had sc inspect my Updated fuse clear the light for me. Under warranty. No charge.

Revise old thread, I end up add some custom mount inserts and seal it up. Because instructions say drop hv main battery, remove half shaft and steering shaft to get access to clevis mount bolts in order to remove it.

i get to drive alot of plaid, and they all vibrate in the rear.. 2021-2022 mostly got some miles on the odo

really ? most people can't differentiate front or rear vibration anyways. but sure keep believe its the front then.

SOFTWARE is to reduce torque at certain mph so reduce vibrate, root cause its the axle can't handle the torque. i confirmed this with swapping rear axle left to right to fix the issue.

i Flipped my rear axles left to right, both same part # confirm fix the vibrate when acceleration!

Did my rear drive unit fluid today. SUPER dark. I would change every 20k miles interval

Changed the fuse myself, 5min job very easy. But message still on, Don't have toolbox 3 to reset error. I hope it goes away by itself 😅

Just got this message my S.. Will remove fuse and check part #. If it's battery powered. Then I will get self powered one.

Yes had it done long time ago. Alcantara Never had problem again

So you have tesla service level toolbox 3 software assumes you also have access to repair manual but can't figure out repair and ask general public for help.

No it won't have horn button for sure. Because in order to add airbag springs loaded require add more hardware and wiring, since that requires new contracts vendor produce new parts

A worn ball joint pop after 6yrs of use, now owner blame bad part and complain on forum. Should of get it replace sooner. Maybe pay a 3rd party instead, probably cheap out didnt pay the $200+ diagnose fee tesla charge to look for the noise. It's common senses when suspension make noise...

If your battery is V1 (2012-2016.).. need to drop battery - 3hrs rate vary battery v2 (2016.5 - 2020 ) pyro its locate on passenger side bottom .5 hr rate service manual; replace pyro fuse are easy, disconnect 12v battery and change pyro fuse but need toolbox to enter service mode plus to write...

is the module new? crashed module require srs specialist to reset before it can work.

if you short communication lin. alot of things can happen. try to start over, plug everything back to factory and reset your car.

you should check the pin #5 is lin communication wire . if you plug it in. you actually short it to ground . the turn signal doen't flash or make noise because there's no feedback of led bulb. aka open connection you need to put pin #2 (older) to pin #4. (newer) looks like the rest of the...

no, work around the oem system. this is why not many people can get it done. i cut alot of stuff and make alot of modification to fit the bumper.

i have shop account w/ tesla

yea i know, but the wiring a bit different. i check you guys history and realize yall trying to update front bumper from older x to new x.. i have done update for my model s to newer bumper. therefore i shared my experienced.

oh no, that diagram is for older model s to new model x foglight.. ONLY older model x wire diagram is this. try to match to new model x ( i have no expence with)

correct. once you plug it in. its obvious that the yellow turn light up in parking light mode. relocate the pin #2 to #1 for fog light only. cut the wire #4, don't need that. its for the yellow - side marker. unless you want, can repin that. (see diagram) pin #3 is parking & corner is correct...

i used model x 6 pin foglight and re-pin it. because its differrent layout. because model s don't have signal on the foglight. btw.. 3-pin is the newer can-bus style communication. similar to headlight cannot get that to work.

i decided to skip it. didn't want to throw more money at the car.

no video. Just buy oem front fenders, hood, bumper, from Tesla. and Custom fit the rest. some cuting crash bar, make custom bracket for the front grill & headlights and wiring repins for the fog lights.

i think my fan is bad cause draw more current to the relay, it make light screeching sound like a worned bearing.

My ac work erratic. Found passenger side fan not work. Here is mine melted condenser fan relay. I guess its common fail. Locate small box next to main frunk fuse box.

They told you why they charge you diagnose fee for aftermarket wiring. why don't you remove those 2 wires and so they can diagnose why your diagnose port is not powering on.. why you have to give them hard time like a "karen"

damn $20k+ in interest

i don't post nothing online. if you look for confirmation answere is yes its posible to do converstion . Not easy tho.

damn, look like you used regular flare wrench on it. you only had 1 chance. try the enclosed flare wrench.. and add some heat n rust buster on it.

lol damn, that's alot of work.

the main switch need to switch over, custom cut somehow. i already check wiring diagram.

12k + trackdays hard driving miles lol

no silly, anytime misaligment axle will cause vibration.. go read up on lifted trucks.

Ricer Life lol

Driveline vibration is normal caused by excessive driveshaft angle mostly common on Model X due to ride height high. Adjust your suspension default to low mode!

i use about $3.5k free supercharging per year.. that's $10k saving 3 years

yea convert to new model s door panel. im in the process looking for a good deal one on ebay

new tesla owner will spend $10k on ppf or color change

thats's the slight taller duckbill style ebay spoiler .. lol

Amazon $20 horn kit . come with two horns, relay wire and toggle button.

that ebay lip look hideous

im a mechanic, i know all these stuff. and i tried all of it.

lol no sound if hood is close. this horn sound won't travel if its inclosed! FAIL

yes, use the hammer