Search results

still available? I need the hardware if possible

option 4: find someone who can help on TMC @DaBase was able to activate 2nd row heating and ambient lighting on MCU2, model s, latest firmware- hardware for new features needs to be installed already obviously. Price is reasonable- about half of Tesla's cost estimate to "investigate" why my HW...

I just wanted to add - this was the correct solution for me :) @DaBase was able to activate 2nd row heating and ambient lighting on a MCU2, model s, latest firmware- hardware for new features needs to be installed already obviously. Price is reasonable- about half of Tesla's cost estimate to...

“Whether you think you can, or you think you can't – you're right,” here are the options that I investigated before doing the mod: Free: ask the service tech nicely to enable the config for a few DIY items the car is in for service. It worked for me, the tech was impressed by the DIY mods too...

Forgot to add - after this is step, pin 1 and pin 2 on the big connector will be for the headrest motor, just as @yangotang speculated.

OK this sounds like enough demand! hold on to your seat buttons ;) First you must realise a little about how Car OEMs work. LK makes the seat control buttons for Mercedes before Mercedes decide if they want to have moving headrests in the W164/W251 without memory seats. The LK engineer designs...

Hey @yangotang @philip295 I have done something similar for headrest control inspired by your efforts using the OEM Tesla switches: take a look: other controls: Any interest in a How-To?

Also some guidance on cutting the side seat trims and some part numbers that will help. To cut the button space out, buy spare seat side trims from tesla for about £10 each, cut these separate to rest of the install. The part numbers are: 1ST ROW LEFT HAND SEAT SIDE SHIELD OUTER - WRAPPED...

Hi folks just an update I’ve done the swap and mostly was per the thread. The main issue I had was I stripped out a head of one t47 Torx bolt. I drilled it out though. Also I’d advise not opening the back of the old seat- you can cut and reconnect most of the wires from the seat base. The...

Thanks that is all very usedful advice! I was thinking the same, once I get started with the transfer it should all fall into place.. Very useful! I can see these wires on the GEN4 seat wiring diagram from service.tesla.com good to have them labeled though :) I will still need to work out how...

no worries, I tried to convert your PNGs using an online service, not tested these yet though..

This is super helpful, too thanks! I do want the memory to work as well :) So I am clear the wiring for the backrest recliner motor requires 4 pins to be connected or just two? the wiring setup is a little confusing with the information spread out all over the thread. My car is May 2016 build...

Thanks for that :) do you have vector versions of these at all? the plastic shop accept SVG, EPS, DXF, STL, CDR etc

hi thanks for this - but I cannot see anything circled in blue. what am I missing?

Nice work! could you please share the laser cutting template? I am considering this swap and will find someone with a laser cutter, having the file will help me and others :)

Perfect! The full software update fixed an issue for me where the rear view camera would show as black. I think the sccm was running v old software and was sending a signal not recognised by the camera so needed a firmware update.

Is there a step before this- how do I get to the prompt for for the service mode?

Ok problem solved. I reinstalled my original sccm and all was well. I noticed the steering wheel was straight too when put into reverse. The wheels were physically straight the whole time. Then I turned the clock spring in the “new” sccm one turn to the left, to counteract the turn to the...

I have not done a full redeploy, how could i do that? I will check the yellow sccm to car connector again. I think I have a better idea of the issue. When I do a cold reboot (disconnect battery etc, before the error appears, if I put the car in reverse the reverse camera lines are showing the...

@samppa I have an issue. I’ve replaced the sccm in preparation for the heated steering retrofit. The part number is the one ending 57 and it has the extra pins. I have added the new steering wheel but the buttons and the airbag are the same. After every cold boot and full turn to the right...

also, see DIY Power Lift gate for Tesla Model S Walkthrough Video getting both to work may not be possible

have a look at this: DIY Power Lift gate for Tesla Model S Walkthrough Video also, it seems you have the v2 kit that does not light up the switch