Search results

I didn’t want to risk it as you can see it’ll definitely rub the thing sticking out of the knuckle with any flex when turning or something. Yes definitely will take pics. Still need to install the coilovers to lower the front as there’s a big gap.

So with a lot of research and double checking with what others have on their setups, I had my fingers crossed. I think having the 4mm spacer saved the setup. I was unsure about the front rubbing but wow, it was clean. 🙏🙏😮‍💨

What’s the offset on MRR? I didn’t want to go down to 35s as it’ll be too rough. Need more sidewall.

I’m planning on doing Rotiforms Tuf-R. Only came in 20x10.5 et 45. Going to put a 4mm spacer on the front to give me some room from the arm.

I just dont want to rub the fronts. I think 295 might be a bit too much with my offset. I'll probably go with 275 square.

looking good, wish Tesla gave us options for coloured seatbelts.

Yeah I think a 5mm spacer should do the trick. Hopefully.

Yeah I dry tested without tires and I wanted to see how close. Definitely need a bit more wiggle room. I really liked the wheels but they only come in 10.5 with that offset. I think I may for sure need a 5mm spacer.

Bump

I want to triple check with you guys. Have a set of wheels 20x10.5 et45. Thinking of putting 275/40/20 front & 295/40/20 rear. That should be fine for the front suspension right? I’ll be lowering it with coilovers after just to tidy things up.

What lip is that

Use this dude. Wheel Offset Calculator

I want to triple check with you guys. Have a set of wheels 20x10.5 et45. Thinking of putting 275/40/20 front & 295/40/20 rear. That should be fine for the front suspension right? I’ll be lowering it with coilovers after just to tidy things up.

I too have the gloss black ones. How was your fitment? The rears were decent but the fronts were a bit off.

finally got the new color matched carbon front lip on. Been meaning to install it.

I got my Maier carbon front lip finally on and color matched it.

50? does that not rub the front? I had the hem inductions on 265/45 and it was rubbing the front on lock.

what front lip is that, is that custom?

You cannot tell in videos or pictures unless you have them in hand. Same thing as buying any Tesla. You pay for that much for a car and you get poor quality of a car. What's any different.

Got to finally test the new Alpharex Nova headlights. I think first in BC. Pricey but yolo. Few things: OEM DRL is brighter in daylight. I think OEM high beam is brighter also. Not sure if these are adjustable to lower or higher the headlight beam. Seems fine right now but I like tinkering.

SR. wheels are 9.5 with 30offset

yup I'm currently running 275/45/19. fits like a dream. drives smoother. 40s are too stiff still

I like the version 2 way better. more simple and clean.

ouch, probably at high speeds there's too much downforce on that type of lip. The reason why I don't really like the ones that have openings like what you have installed. Too much risk of it getting pulled down.

liking the lip, have the same one :) how thick are your spacers lol

yeah I had to go through a couple vendors at first and they told me they don't produce it anymore until one vendor went through and it was cheaper than the first ones I tried buying from.

Haha that would be a fun side project. I would just fill it in then sand it smooth then paint. But yeah it doesn't look that nice when its glossy because it'll bring out the lines more, matte is the way to go.

yeah that's what I thought too, the vertical lines were a bit much. If they got rid of that then it would be golden. Yeah their matte carbon look isn't great but I like the matte look as it gives contrast with the glossy black and the matte plastic bits.

yeah you can find them online everywhere. I bought it from Aliexpress from a trusted vendor. Its without markup on eBay so I'd rather go there.

yeah its the cleanest looking lip but don't like how it comes to a point with a curve on the bottom. If the centre section was a bit more beefy it would be a good lip for sure.

I only have one picture right now.

yup I ended up getting it. Fitment is really good.

looks ugly imo. why so aggressive

nice lip, have the same one :)

nope

its to prevent on burning your hands lol.

nice wheels. Model 3?

https://www.ebay.ca/itm/403079176956?hash=item5dd96422fc:g:mUoAAOSwYTZhG3JL https://www.ebay.ca/itm/363509057507?hash=item54a2d407e3:g:-vUAAOSwsmJhG3lz https://www.ebay.ca/itm/363509021098?hash=item54a2d379aa:g:hYkAAOSw1D9gpdCd

what wheels are those? specs?

haven't posted my Y yet but recently installed a lip. Not too shabby I think.

nice nice, I was waiting on some pictures from the cmst body kit to go up online. Hows the fitment on the side skirts.

Should be good enough. By the installation video they just screw into the bumper from under since the front end is slightly angled upwards anyways.

yeah nice. This is splitter I see a lot, very aggressive. looking for a more subtle look.

aight I'll wait for your pics

Been on the look out for front lips but either they look meh or too aggressive looking. Thoughts on this lip that popped out recently? Anybody got any installed?

Did you get those wheels from the model 3?

do you have pictures of the rear wheel fitment? is 40et flush? I was thinking of getting +35 in the rear so want to see how aggressive that will be.

yeah why beige, weird. I guess they can't get it in white.

just buy it from Aliexpress, its half the price.

it came debadged ?? that's weird