Search results

Anyone have an update on #1297? It’s back up for auction ! Does anyone know if someone with the knowledge tried to revive the battery pack?

No had sheet 1 out disconnected 4 bad cells in 1 of the bricks then reinstalled it Numbered all the bmb and installed them as removed?

this is what I’m getting on the display After reinstalling the ESS Bought it not running so some issues may have been prior to me owning it

Can’t check logs I’m getting bmb no data fault? Should I be able to get it out of tow mode buy jumping 12v in rr wheel well?

So I had remove the main battery due issues with one sheet Removed the sheet and disconnected a few cells (4) in the brick that were draining it down . Charged the battery and it had over 360 volts when I just installed it! Nothing comes up unless I jump with 12 volts in in rh wheel well? I get...

Thank you! ? I have 1 brick in one cell (which I have out of the eSS ) that charges upto 3.6 but then drops down over night to 1.9 ? I figured a shorted cell in the brick draining it down but can’t seam to find it ? I tried applying higher charging rate directly to brick grid. Looking for cell...

Any way to test the Aps that’s inside the ESS while it’s out ? Are there lithium’s inside the aps that should be charged up ?

Do u by chance still have this?

Looking for roadster good and fenders?

What holds the sheet in the case other than the screws? The one sheet I’m trying to remove is loose but something else seams to be holding it in yet? Do you need to remove the alum crossmember from the bottom of the case?

Please confirm the input on Nicks designed charging boards? Looks like the left input to be negative and the rest are all positive?

Need a rh headlight if you still have one Thanks

Thanks good to know I’m in wayne nj working on my salvaged roadster but I have a man cave in Pine Island Maybe we could meet up in the near future

I know I had seen a list of dead or salvaged roadsters some where on the site but can’t seam to find it again? Can someone point me to it Thanks

any roadster owners close to Wayne NJ?

any roadster owners close to Wayne NJ?

Can you help me with this? I sent the Gerber file to a company to build the boards . I do not know how to read the files since I’m not an electronic wizard

Thank you for the cautions! I do understand the risks! I want to make sure I’m going about in a way that has been successful for others.

Yes that’s what I ordered What to use for a charger?

I am now the proud owner of 961(I think) And plan to bring it back to life!

Can you supply me with the part numbers for the ends? As well as what connector needed for charger end? And what chargers you suggest? Thanks

Does Nicks Gerber file included populating them? As well as ends required? What were you referring to when you stated it’s expensive to populate them ? What chargers would you recommend I did order some monitoring boards as listed in your thread to nick . What else do I need to get going? Thanks

Ok thanks Please tell me where to have them made? And what chargers to use Approx cost?

Thanks do you have this set up I can rent ? Borrow or buy? Or boards with ends set up Tom

I have 6 troubles on the display ! Including id1906 unable to exit tow mode” So I’m guessing the HV battery is dead? Preventing me from exiting tow mode It appears the car has not been charged since January And can’t get to eSS menu What to do ? Can I call you?

Got the vds. Powered up ! Unable to exit tow mode? Most likely due to low power? Can’t charge in tow mode! What’s the work around for this ? Any help appreciated Thanks

The bmw charger is only 10 amps

Figured it out

Ok figure out the charger needed 12 volts to activate it! N/p Sing an I8 charger @ 10amps to try and recover the pack. Suggestions?

So peter we are talking about connecting to terminals Ac1 and Ac 2 in the set port which appear to go to charging port correct? But how to get the charger to output voltage?and what should it be?

So peter we are talking about connecting to terminals Ac1 and Ac 2 in the set port which appear to go to charging port correct? But how to get the charger to output voltage?and what should it be?

Thank you very much for all your help

Thank you Peter Question I have a newer model 40amp 115 Tesla charger What voltage readings should I get checking the out put? I get 11.75 BEC on small pins and nothing on the two large pins? Is the charge bad or is the a signal required from the car? Also right now I don’t what to spend $ for...

Do you still have it?

want to buy can Jr or can sr for roadster! Or borrow if possible Bought a salvaged 2010 and need to see if batteries will charge Thanks

I need a right

Thanks Peter Where do I find the APS leads in the rear ?

Thanks peter if you can email them to me that would be great [email protected]

Ok so if the battery is dead ! I assume the car is in park? How to get it to roll or get out off park?

Peter I see you sell a Can Jr. Will that work for me or do I need to look for a Can Sr?

Thank you for your replies I have a Tesla charger from a newer vehicle which I believe will work on my roadster with the correct roadster adapter I need a roadster adapter Anyone out there have one they are willing to sell ?or if someone might tell me where I might get one Thanks

Will this plug into a 2010 roadster Is it called the Canjr ?

Don’t have the car yet

well I bought a salvage 2010 roadster No charging cable I’m sure it has not been charged for some time Woundering if it’s possible to make a simple charging cable?